Bonding

How to Configure Mikrotik Bonding With Cisco Switch

Bonding is a technique that allows aggregation of multiple Ethernet links into a single virtual link, that provides higher data rates and providing failover. For  Configure Minimum License require level1 and need minimum 2 NIC card. To add Bonding interface in R1 and R2 /interface bonding add name=bwbond slaves=ether1,ether2 / ip address add address=172.16.0.1/24 interface=bwbond bonding interface needs a couple of seconds to get connectivity with its peer On Cisco Switch in L3 Mode interface… Read More

Continue Reading

How to Fix File Sharing Problem on Windows

Fix File Sharing Problem on Windows Check your PCs are on the same network WIFI or LAN and also same workgroup (click Start, right-click Computer and select Properties; in XP you need the Computer Name tab). Is File and Printer Sharing enabled? Check from Network and Sharing Center in Vista/Windows 7 ensure your network is Home or Work. In Windows 7 click Choose homegroup and sharing options > Change advanced sharing settings; in XP right-click a folder and choose… Read More

Continue Reading

Juniper Switch VLAN,TRUNK,Management VLAN Configuration

1. Create a vlan with the name “MKT” and assign a vlan id of 10 Create a vlan with the name “ACC” and assign a vlan id of 20 # set vlans MKT vlan-id 10 # set vlans ACC vlan-id 20 2. Assign two interfaces (Gigabit Ports) to the “MKT” vlan #set interface ge-0/0/0 unit 0 family ethernet-switching port-mode access #set interface ge-0/0/0 unit 0 family ethernet-switching vlan members MKT ->To set a trunk port… Read More

Continue Reading

How to show MAC Address to Juniper Switch

For view Mac Address in Juniper Switch It will show all MAC Address learn from all of your switch network. #run show ether-switching table It will show all MAC Address learn from interface ge-0/0/16.0 #run show ether-switching table | match ge-0/0/16.0 It will show all MAC Address learn from interface ge-0/0/6.0 # run show ethernet-switching table interface ge-0/0/6.0 It will show all MAC Address learn from VLAN Configuration #run show ether-switching table | match Configuration Show… Read More

Continue Reading

How To Configure Inter-Vlan Routing in Cisco Router

  Configure Inter-Vlan Routing in Cisco Router vlan divide broadcast domain. when need one vlan communicate to other vlan that time traffic must be routed between them. this called inter-vlan routing. Step 1 Configure sub interface in Router. IOU1#conf t Enter configuration commands, one per line.  End with CNTL/Z. IOU1(config)#int e0/0 IOU1(config-if)#int e0/0.10 IOU1(config-subif)#en IOU1(config-subif)#encapsulation do IOU1(config-subif)#encapsulation dot1Q 10 IOU1(config-subif)#ip add IOU1(config-subif)#ip address 192.168.10.1 255.255.255.0 IOU1(config-subif)#no sh IOU1(config-subif)#int e0/0.20 IOU1(config-subif)#encapsulation dot1Q 20 IOU1(config-subif)#ip address 192.168.20.1… Read More

Continue Reading

Skype Separate Bandwidth in Mikrotik

 If anyone want to separate Skype bandwidth in Mikrotik. please execute below configuration. /ip firewall layer7-protocol add name=skypenack regexp=”[\\\\|\\xd5]” /ip firewall mangle add action=add-src-to-address-list address-list=skype address-list-timeout=1h chain=forward disabled=no layer7-protocol=skypenack packet-size=39 protocol=udp  add action=mark-connection chain=forward connection-rate=0-50k disabled=no new-connection-mark=conn_skype passthrough=yes protocol=udp src-address-list=skype add action=mark-connection chain=forward connection-rate=0-50k disabled=no dst-address-list=skype new-connection-mark=conn_skype passthrough=yes protocol=udp add action=mark-packet chain=forward connection-mark=conn_skype disabled=no new-packet-mark=skype passthrough=no ####Below For Mange Skype Bandwidth in Mikrotik /queue simple add name=skype-bw max-limit=2M/2M packet-mark=skype priority=8 queue=default or /queue tree add… Read More

Continue Reading

How to Flush DNS Resolver Cache on Windows

If you change your DNS server address. the change not effect immediately. Windows utilizes a cache that remembers DNS responses it’s received, Saving time time when you get to similar addresses again later on. To ensure Windows is getting addresses from the new DNS servers instead of using old, cached entries, run the ipconfig /flushdns command after changing your DNS server.

Continue Reading