How to configure Service Policy in Juniper

  Juniper Interface Bandwidth Limit #set firewall policer 8mb if-exceeding bandwidth-limit 10m #set firewall policer 10mb if-exceeding burst-size-limit 1m #set firewall policer 10mb then discard [10mb is policer name. burst size should be 10% of bandwidth limit] #set interfaces ge-1/0/0 unit 0 family inet policer input 10mb #set interfaces ge-1/0/0 unit 0 family inet policer output 10mb [Call 10mb policer to your desire interface]

Read More

How to configure ip address in juniper switch

  First need to create vlan and from which vlan you want to access remotely. now we create vlan name management vlan and vlan id 100. #set vlan management vlan-id 100 #set vlans management l3-interface vlan.100 Assign IP address in this vlan 100 #set interfaces vlan unit 5 family inet address 192.168.100.50/24 now you can able to connect remotely via telnet or ssh service

Read More

How to configure spanning Tree in Juniper

  spanning Tree protocol help to prevent Broadcast storms. its defined IEEE 802.1D standard provide faster spanning-tree convergence after a topology change. Configure spanning Tree protocol [edit] set protocols rstp (enable RSTP) set protocols rstp bridge-priority 20k set protocols rstp interface ge-0/0/2.0 disable set protocols rstp interface ge-0/0/2.0 cost 1000 set protocols rstp interface ge-0/0/2.0 edge <– Same as Cisco portfast command. set protocols rstp interface ge-0/0/2.0 mode point-to-point For the backup link. Verify spanning Tree protocol [edit] show protocols stp | display set show spanning-tree bridge show spanning-tree interface show ehternet-switching interface

Read More

How to configure telnet in juniper

  juniper configure telnet service # set system services telnet # set system services telnet connection-limit limit;  (Default connection-limit limit 75. i configure 1 to 100. its define maximum connection simultaneous  per protocol) # set system services telnet rate-limit limit;  (its define maximum connection per minute. default is 150.When you configure a rate limit, the limit is applicable to the number of connection attempts per protocol ) # commit commit use for save configuration.

Read More

How to set factory default juniper

  Factory-Default Configuration Use load factory-default to load a system’s factory-default configuration  # load factory-default  [It will be load as a Factory Default as like a new device. Previous all configuration will be delete] Need set root password to activate or Initial  configuration: # set system root-authentication plain-text-password  New password: Retype new password: # commit commit use for save configuration.

Read More

How to Configure root password in Juniper

  Setup Juniper Root Password root password is mandatory in juniper. without root password configuration not save or commit. by default password is encrypted. # set system root-authentication plain-text-password    [Enter] New password: Retype new password: Here New password is your desire password and Retype new password is same as you given

Read More

How to configure Trunk in Juniper

  Configure Trunk in Juniper pass only MKT and Sales vlan Traffics in trunk port. #set interface ge-0/0/3 unit 0 family ethernet-switching port mode trunk vlan member MKT #set interface ge-0/0/3 unit 0 family ethernet-switching port mode trunk vlan member  add Sales pass all vlan traffics in trunk port. #set interface ge-0/0/6 unit 0 family ethernet-switching port mode trunk vlan member all  

Read More

How to configure VLAN in Juniper

  Configure VLAN in Juniper Vlan means virtual local area network. its separate workstation in logically. in this tutorial we configure VLAN in juniper switch. Step 1 Create Vlan with the name MKT and assign a vlan 10 Create Vlan with the name Sales and assign a vlan 20 # set vlans MKT vlan-id 10 # set vlans Sales vlan-id 20 Step 2 Assign Vlan in physical interface #set interface ge-0/0/0 unit 0 family ethernet-switching port-mode access #set interface ge-0/0/0 unit 0 family ethernet-switching vlan members MKT #set interface ge-0/0/0 unit 0 family ethernet-switching port-mode access #set interface ge-0/0/0…

Read More